I. Product Summarization
.Product constitute
1. LED-WiFi Controller | It is the core of product, responsible for receive control signal and control LED equipment. |
2. RF remote control | In the condition of not use the mobile phone as remote control, you can choose RF remote control to control LED. |
3. A disk | Include IOS operating system and Android operating system mobile soft. |
2. Summarization Use WiFi technology can make our control range more wider, can get rid of narrow space constraint, in building can control more than 50m, in outdoor can control more than 100m. In the condition of not use the mobile software, also can use the remote control to control, very convenience, bring many choices for you.
II. Technical Parameters
1. Remote control technical parameters
- 1: Working temperature: -20-60?
- 2: Power supply method: AAA*3
- 3: Supply voltage: 1.5V*3
- 4: Standby power: 0.015mW
- 5: Standby current: 3uA
- 6: Working current: 200uA
- 7: Emission current: 10mA
- 8: Remote control distance: about 50m
- 9: Standby time: 6 month
2. Software technical parameters
- 1: Name: Dream Color
- 2: Runtime platform: Android version support Android system(better one can support Samsung,
- HTC), IOS version support IOS system, equipment must have WiFi function.
- 3: Language: English
- 4: Category: communications
- 5: Free, green, no plug-ins
3. Controller technical parameters
- 1: Working voltage: DC5–24V
- 2: Output control: SPI signal output
- 3: Output current: 4A*3
- 4: Connect mode: SPI signal wires(DATA, CLK)
- 5: External dimension: L107*W65*H30?mm?
- 6: Receiving sensitivity: 802.11b DSSS(-5dBm)?802.11b CCK (-10dBm)?802.11g ?OFDM(-15dBm)
III. LED-WiFi Controller Function Instruction
1.Working state instruction
Indicator light | Function table |
Power | Power indicator light, long-time bright shows power supply normally |
Wifi | Free time long-time bright, have wifi data enter flicker, configuration wifi Ssid off |
Link | Have wifi date enter, then flicker, no wifi data, then off. |
RF | Have RF remote data or press key operate, then flicker, free time off. |
2.Setting SSID number
The dial code is used for setting LED-WiFi controller Ssid number, corresponding table as below. Form 0 to 15, have 16 code in total, so our Ssid number fasten to LN001 to LN016. That means use our product in same small area can set 16 mutual isolation LAN, once the dial code changed after switch was dialed, Ssid number immediately be modified, so you need to note that it need to search and connect again.
code | SSID |
0 | LN001 |
1 | LN002 |
2 | LN003 |
3 | LN004 |
4 | LN005 |
5 | LN006 |
6 | LN007 |
7 | LN008 |
8 | LN009 |
9 | LN010 |
A | LN011 |
B | LN012 |
C | LN013 |
D | LN014 |
E | LN015 |
F | LN016 |
3. Connect LED, Power supply port
LED
4. Match Key function
Use method: first, press the controller “Match” key, at the same time press any key of the remote control, more than 2s, now the remote control indicator light RF will flicker 3 times, release “Match” key, then finished.
5. Function key function
“Function” key is a composite button, it have switch and mode change function.
Function instruction: long-time(more than 2s): on off;
Short press(less than 1s): mode change.
6. Remote control function instruction
1. ON/OFF 2. pause 3. MODE+ 4. MODE-
5. Color pulley touch button 6. Brightness+ 7. Brightness-
8. SPEED+ 9. SPEED-
1. Controller panel have 64 touch point, and the function as follow:
1. ON/OFF,you can turn on/off controller output at any time;
2. Pause,at dynamic mode, you can stop the controller at the current state;
3. This button have 2 functions :
①Mode + choice key, when current control pattern is pulley pattern (color), if must
realize the pattern (color)in the controller, can press this key.
②mode switch button, for the current control mode, you can switch M + key which
is specified mode (color) in the table.
4. This button have 2 functions :
①Mode – choice key,when current control pattern is pulley pattern (color), if must
realize the pattern (color)in the controller, can press this key.
②mode switch button,For the current control mode, you can switch M + key which
is specified mode (color) in the table.
5. The output brightness control key,every time you press this button, the brightness series
add 1, altogether 32 levels.
6. The output brightness control key,every time you press this button, the brightness series
minus 1, altogether 32 levels.
7. The output speed control key,every time you press this button, the brightness series
add 1, altogether 99 levels.
8. The output speed control key,every time you press this button, the brightness series
minus 1, altogether 99 levels.
9. Color pulley touch button, static mode choose button, up to 55 touch points.
this button have 2 functions:
①static color choose button, when current control mode is the mode of M
key(color), if you want to realize static color ,can press this button.
②pulley color choose button, can choose from 55 kinds of static mode
(the color from pulley).
2. Power supply management: stop to use the remote more than 20s, the remote will enter the
standby state (untouchable state), to extend the battery life; slightly shake once, then the
remote will come back to the normal working state (touchable state).
Notice:This remote control only can change the pattern, the brightness, the speed, if you want
to change the controller IC model, the IC support point, the RGB sequency, then must
connect WIFI through cell phone to change.
7. Controller built-in mode table
Modes | Mode instruction | ||
1 | Static red | ||
2 | Static green | ||
3 | Static blue | ||
4 | Static yellow | ||
5 | Static purple | ||
6 | Static cyan | ||
7 | Static white | ||
8 |
Additional information
Reviews (1) 1 review for WiFi Dream Color LED Strip Light Controller 83 Changes for IOS Android SystemYou must be logged in to post a review.
Sign in No account yet? Create an Account |
Luke.Wied (verified owner) –
Excellent product great to deal with