Product Description

Specifications

• Working temperature: -20- 60 ℃
• Supply voltage: DC12V
• Product size: L90×W58×H26mm
• Weight: 126g
• Current：<60mA
• Effects model: 94
• Maximum control points: 1024 (Low-speed) points, 2048 (High-speed) points
• Fit for chip LPD6803、TM1803、UCS1903、WS2811 TM1812、TM1809、WS2801、 TLS3001、 TLS3008 、P9813 、LPD8806 、TM1829 etc.

Controller menu settings: (Defaulting boot when power is on, the controlled IC are 50 points and high-speed mode)

• (1).Connect the light bar well before taking power according to "wiring diagram". After power controller has been at work. It is a normal phenomenon that the light bars may be not bright. Because the following steps must be set by before the light bars are bright.
• (2).Please press the "On / off" button to take the controller off before setting the menu.
• (3).Press the "up", "down" button one time at the time, and LED would be bright at this moment. Then press the "Mode / Speed" button to get into the menu settings screen.
• (4).The first setting screen is for "High-speed, low-speed settings", and the LED would display "S-HI" or "S-LO". Then press the "up" and "down" button to select the mode. (If the IC on the light bar is high-speed mode, you should choose "S-HI", and choose "S-LO" when low-speed.) The factory default is for the high-speed mode.
• (5). Continue to press the "Mode / Speed" button to enter the second screen-"Control points setting". The LED display 4-digit is for the number of control points. To plus or minus the number by pressing the "up" and "down" button. (Long pressing can adjust quickly)。The factory default is for 50.
• (6). After setting well, press the "On / off" button to save and exit.

Function of button(Controller is in playing state):

• (1).ON/OFF: ON/OFF button，it can open or close output.
• (2). UP: Mode + / Speed +
• (3).DOWN: Mode -1/ Speed -
• (4).Mode/Speed: Mode adjustment / speed adjustment function switch (The first LED displays H for model adjustment, shows S for the speed adjustment.)

Note: After powering, the red light would bright. And each press, the green light flash one time.

Synchronous controller system description

Synchronous control system can be made of any number of controller connections. Each of the sub-controller would follow to the first master controller to achieve a permanent synchronous change. And there is not delay.
After connecting the wiring diagram, the sub-controller need not be set. It will be in accordance with the master to controlling the speed and mode change. (That would be not synchronous when powering. You could close and open to be synchronous) When master is working, and the sub-control working well, the green signal light of sub-control would flick. The digital LED display the mode in operation.

The operating instructions of editable mode (133rd mode): (The symbol * indicates an unknown number)

This mode is a combination mode of editing, you can edit scenes from 2 to 20 (1 to 132 mode) into a circular pattern. Each pattern can be set individually for each change of speed. It can automatically identify the set of patterns and automatically loop the pattern.

• (1). Press the "Mode / Speed" and "Up" button once at the same time to enter the edit menu. LED is lit and display "-01-"."-**-" screen indicates the scene number of current editor. At this point you can select the number you want to edit a scene by the "+","-" keys.
• (2). After selecting the scene you want to edit, press the "Mode / Speed" key and display "H ***".That is the setting current scene mode. Then you can press "+","-" key to choose the scene mode, and observe the current results through the light bar. While the LED displaying "H000", that is to say the scene is not set patterns.
• (3). After choosing a mode, press "Mode / Speed" key once and display "S0**".It is the speed of the current scene mode. Then you can change the speed of the scene mode by the "+","-" keys. And you can observe the effect of the current mode through the light bar.
• (4). After choosing the speed, press the "Mode / Speed" key to return to the selection screen "-**-". At this point you can select the next need to edit the scene by the "+","-" key. Or press the "On / Off" key to exit and save settings.

When the setting scene is less than 20, it must start from the first number (Because the 133 rd model starts running from the scene "01"), and need to set the no setting scene mode for "H000". For example, setting up five scenes and combine into 133rd mode. Enter the editable menu, and edit "01"to"05"scene modes and their speed (Can not follow the order). After editing well, you should check whether the "06" scene mode is the "H000". If not, change it by "+"and"-" key.

Program Description

Packing List